Gear Geometry国外齿轮设计软件V1.42免费版

Gear Geometry国外齿轮设计软件是一款英国的齿轮设计软件GearDesignPro，支持斜齿，图形显示，多种测量方法显示，公制、英制单位互换，绝对不可多得的好东东。感觉开发者对齿轮有深入的研究,只是不知道软件的价格是不是很高,性价比如何,以前破解的GEARDESIGNPRO这个版本和国内一些设计软件基本相似,没什么高明。

齿轮参数：

PINION→小齿轮 WHEEL→大齿轮 

Normal Module (mm) →法向模数 

Pressure Angle (degrees) →法向压力角 

Helix Angle (degrees) →分度圆螺旋角 

Helix Hand→螺旋旋向（left 左/right 右） 

Centre Distance (mm) →中心距 

Face Width (mm) →齿宽 

Edge Chamfer (mm) →齿端倒角（棱） 

Desired Ratio →要求的传动比 

Number of Teeth→齿数  

Sum of Add. Shift Coeff.→总变位系数（法向） 

Add. Shift Coeff.→单个齿轮变位系数（法向） 

Add. Shift Distribution→变位系数分配 

nominal Thickness →公称齿厚 

Backlash (Normal) (mm) →侧隙（法向） 

Backlash Distribution →侧隙分配 

Finished Thickness →成品齿厚 

Outside Diameter (mm) →外径 

Outside Diameter Chamfer (mm)→齿顶倒角（棱）（修缘） 

Root Diameter (mm) →齿根直径 

Root Fillet Radius (mm) →（齿条刀具）齿顶圆角半径 

Basic Rack Proportions →基本齿条参数（输入/标准/计算） 

Basic Rack Addendum (/Module) →基本齿条齿顶高系数 

Basic Rack Dedendum (/Module) →基本齿条齿根高系数 

Root Fillet Radius (/Module) →（基本齿条）齿根圆角半径系数 

Protuberance →齿条刀具齿顶触角宽度 

Allow Outside Diameter Reduction →允许齿顶圆减小 

Keep Pinion and Wheel Same →保持两齿轮齿顶高相同 计算结果： 

PINION小齿轮     

WHEEL大齿轮 

Number of Teeth→齿数 

Normal Module (mm) →法向模数 

Pressure Angle (degrees) →法向压力角 

Helix Angle (degrees) →分度圆螺旋角 

Helix Hand →螺旋旋向（left 左/right 右） 

Reference Diameter (mm)→分度圆直径 

Addendum Modification Coeff. →变位系数（法向） 

Outside Diameter (mm) →外径 

Outside Diameter Chamfer (mm)→齿顶倒角（棱）（修缘） 

Root Diameter (mm) →齿根直径 

Root Fillet Radius (mm) →（齿条刀具）齿顶圆角半径   

Centre Distance (mm) →中心距 

Face Width (mm) →齿宽 

Edge Chamfer (mm) →齿端倒角（棱） 

Form Diameter (mm) →渐开线起始圆直径 

Base Diameter (mm) →基圆直径  

Thickness (nominal transverse) (mm) →（公称端面）齿厚 

Thickness (nominal normal) (mm) →（公称法向）齿厚 

Thickness (finished transverse) (mm) →（成品端面）齿厚 

Thickness (finished normal) (mm) →（成品法向）齿厚 

Measurement Over Balls(finished) (mm) →跨棒距 

Ball Diameter (mm) →量棒直径 

Chordal Span (mm) (finished) →（成品）公法线长度 

Number of Teeth to Span →跨齿数  

Contact Ratio (Transverse) →端面重合度 

Contact Ratio (Axial) →轴向重合度 

Desired Ratio →要求的传动比 

Actual Ratio →实际传动比  

Backlash (Transverse) (mm) →端面侧隙 

Backlash (Normal) (mm) →法向侧隙 

Backlash (Radial) (mm) →径向侧隙 

Backlash (Transverse circular) (mm) →端面圆周侧隙 

Backlash (Normal Circular) (mm) →法向圆周侧隙  

start of active Profile Diameter (mm) →有效齿廓起始直径 

Lowest Single Tooth Contact (mm)   →单齿啮合最小直径 

Highest Single Tooth Contact (mm)   →单齿啮合最大直径 

End of Active Profile Diameter (mm) →有效齿廓终止直径  

Transverse Pressure Angle (deg)   →端面压力角 

Transverse Module (mm) →端面模数  

Working Pitch Diameter (mm) →节圆直径 

Working Normal Pressure Angle (deg) →法向啮合角 

Working Transverse Pressure Angle (deg) →端面啮合角 

Working Helix Angle (deg) →节圆螺旋角  

Face Width Offset (mm) →齿宽调整 

Active Face Width(mm) →有效齿宽  

Base Radius to Form Radius (mm) →渐开线起始圆到基圆的距离 

Form Radius to SAP Radius (mm) →有效渐开线起始圆到渐开线起始圆距离 

Bottom Clearance / Module →顶隙系数 

Normal EAP Thickness / Module →有效齿廓终止点法向厚度系数 

Normal O.D. Thickness / Module →齿顶法向齿厚系数 

Root Fillet Radius / Module →（齿条刀具）齿顶圆角半径系数  

Base Helix Angle (degrees) →基圆螺旋角 

Normal Base Pitch (mm) →法向基圆节距 

Transverse Base Pitch (mm) →端面基圆节距  

ISO Quality grade →ISO 精度等级 

Single radial composite deviation (mm) →一齿径向综合公差 

Total radial composite deviation (mm) →径向综合总公差 

Single pitch deviation (mm) →单齿距公差 

Total cumulative pitch deviation (mm) →齿距累积公差 

Single tangential comp. deviation (mm) →一齿切向综合公差 

Total tangential comp. deviation (mm) →切向综合总公差 

Profile form deviation (mm) →齿廓形状公差 

Profile slope deviation (mm) →齿廓倾斜极限偏差 

Total profile deviation (mm) →齿廓总偏差的公差 

Helix form deviation (mm) →螺旋线形状公差 

Helix slope deviation (mm) →螺旋线倾斜极限偏差 

Total helix deviation (mm) →螺旋线总偏差的公差  

Tangential force (N) →圆周力 

Radial force (N) →径向力 

Axial force (N) →轴向力